industrial boiler flue gas dehumidification equipment

Enviroair Industries Beyond The Product

• This integrated system allows both flue gases and fresh air to flow through a single component, reducing installation time and roof or wall penetrations. • InnoFlue® Concentric is UL-1738 and ULC-S636 listed. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.

Learn More

Humidifier - Wikipedia

A humidifier is a device, primarily an electrical appliance, that increases humidity (moisture) in a single room or an entire building. In the home, point-of-use humidifiers are commonly used to humidify a single room, while whole-house or furnace humidifiers, which connect to a home's HVAC system, provide humidity to the entire house. Medical ventilators often include humidifiers for

Learn More

Reviewer for Chemical Engineering Comprehensive

A. Cooling and dehumidification. B. Heating and dehumidification at almost constant wet bulb temperature. C. Dehumidification with dry bulb temperature remaining constant. D. None of these. 19. A _____ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gas-vapor

Learn More

A review of the current automotive manufacturing practice

Mar 01, 2020 · Space heating, industrial process heating, drying, etc. • Energy-efficient automatic compressor • Pressure drop minimisation • Pipes and equipment leak reduction • Proper regulator sizing. Boilers: ThermalEnergy efficiency • Fuel gas heat recovery for boiler feed-water preheat in an economiser. • Hot condensed water recovery. •

Learn More

High-Performance HVAC | WBDG - Whole Building Design Guide

Nov 07, 2016 · Gas-fired desiccant dehumidification packages are located in the outside intake air stream or in the entire supply air stream. Outside air is heated by the gas furnace and is blown over the wheel to regenerate the desiccant. Other forms of heat exchange include: Indirect evaporative cooling (IDEC) uses water-to-air heat exchange to precool air.

Learn More

Mechanical Interview Questions & Answers - Wisdom Jobs

Boiler tubes, usually are made from carbon steel and are subject to. high rates of heat transfer, bending stresses due to uneven heating, especially at expanded or welded joints into headers or drums, external erosion from burners and flue gas, possible corrosion on the boiler

Learn More

Ventilation (architecture) - Wikipedia

Ventilation is the intentional introduction of outdoor air into a space. Ventilation is mainly used to control indoor air quality by diluting and displacing indoor pollutants; it can also be used to control indoor temperature, humidity, and air motion to benefit thermal comfort, satisfaction with other aspects of indoor environment, or other objectives.

Learn More

2018 NORTH CAROLINA STATE BUILDING CODE: ENERGY

C402.1.3 Insulation component R-value-based method.. Building thermal envelope opaque assemblies shall meet the requirements of Sections C402.2 and C402.4 based on the climate zone specified in Chapter 3. For opaque portions of the building thermal envelope intended to comply on an insulation component R-value basis, the R-values for insulation in framing cavities, where required, and for

Learn More

Mechanical Interview Questions & Answers - Wisdom Jobs

Boiler tubes, usually are made from carbon steel and are subject to. high rates of heat transfer, bending stresses due to uneven heating, especially at expanded or welded joints into headers or drums, external erosion from burners and flue gas, possible corrosion on the boiler

Learn More

Influence of Operating Parameters on Chlorine Release and

May 06, 2021 · A 130 t/h biomass circulating fluidized bed (BCFB) boiler combustion system model, considering the chloride release and pollutant emissions during the biomass combustion, was established using the Modelica language. The effects of the biomass feed amount, limestone amount, excess air coefficients, and different ratios of primary and secondary air on the boiler furnace temperature and flue gas

Learn More

Stoichiometry and Process Calculations | Filtration

The transfer of vapour from liquid to gas occurs in humidification operations and the reverse process occurs in dehumidification. Cooling towers, spray chambers, humidifiers, etc. are pieces of equipment used for these operations. In drying a wet solid or a slurry is contacted with dry gas (usually air or flue gas) so that water is

Learn More

(PDF) Design standards _ CONFERENCE BUILDINGS, EXHIBITION

The exhaust air regenerates the desiccant. Enthalpy recovery wheelo Gas-fired desiccant dehumidification packages are located in the outside intake air stream or in the entire supply air stream. Outside air is heated by the gas furnace and is blown over the wheel to regenerate the desiccant.c.

Learn More

Reviewer for Chemical Engineering Comprehensive

A. Cooling and dehumidification. B. Heating and dehumidification at almost constant wet bulb temperature. C. Dehumidification with dry bulb temperature remaining constant. D. None of these. 19. A _____ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gas-vapor

Learn More

Ventilation (architecture) - Wikipedia

Ventilation is the intentional introduction of outdoor air into a space. Ventilation is mainly used to control indoor air quality by diluting and displacing indoor pollutants; it can also be used to control indoor temperature, humidity, and air motion to benefit thermal comfort, satisfaction with other aspects of indoor environment, or other objectives.

Learn More

(PDF) Design standards _ CONFERENCE BUILDINGS, EXHIBITION

The exhaust air regenerates the desiccant. Enthalpy recovery wheelo Gas-fired desiccant dehumidification packages are located in the outside intake air stream or in the entire supply air stream. Outside air is heated by the gas furnace and is blown over the wheel to regenerate the desiccant.c.

Learn More

A review of the current automotive manufacturing practice

Mar 01, 2020 · Space heating, industrial process heating, drying, etc. • Energy-efficient automatic compressor • Pressure drop minimisation • Pipes and equipment leak reduction • Proper regulator sizing. Boilers: ThermalEnergy efficiency • Fuel gas heat recovery for boiler feed-water preheat in an economiser. • Hot condensed water recovery. •

Learn More

Property Managers | Business Energy Services

To increase the efficiency of a boiler by 2 to 3 percent, install an economizer. This device preheats the feedwater (returned condensate). In the case of a 250-horsepower boiler, an initial investment of $6,000 provides an annual savings of more than $3,000.

Learn More

Property Managers | Business Energy Services

To increase the efficiency of a boiler by 2 to 3 percent, install an economizer. This device preheats the feedwater (returned condensate). In the case of a 250-horsepower boiler, an initial investment of $6,000 provides an annual savings of more than $3,000.

Learn More

Stoichiometry and Process Calculations | Filtration

The transfer of vapour from liquid to gas occurs in humidification operations and the reverse process occurs in dehumidification. Cooling towers, spray chambers, humidifiers, etc. are pieces of equipment used for these operations. In drying a wet solid or a slurry is contacted with dry gas (usually air or flue gas) so that water is

Learn More

Humidifier - Wikipedia

A humidifier is a device, primarily an electrical appliance, that increases humidity (moisture) in a single room or an entire building. In the home, point-of-use humidifiers are commonly used to humidify a single room, while whole-house or furnace humidifiers, which connect to a home's HVAC system, provide humidity to the entire house. Medical ventilators often include humidifiers for

Learn More